Aastra AXD Especificaciones Pagina 241
- Pagina / 502
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation and Maintenance Manual - Aastra 5000 AMT/PTD/PBX/0058/4/6/EN
Description des sous-ensembles 01/2011 Page 241
Indicators
The six LEDs described in the table below show the operating state of the card:
TABLEAU 4.53 PRESENTATION OF THE PT2 CARD INDICATORS
This VoIP card has no signalling indicator.
The front panel of the PT2 card includes:
• an "RST" push-button used to reset the card (manufacturer reserved),
• an "NMI" push-button used for an non maskable interruption of the processor
(manufacturer reserved).
4.13.5.4 Hardware configuration
The PT2 card has a CA1 configuration microswitch.
(1) Factory delivery configuration in bold characters
TABLEAU 4.54 HARDWARE CONFIGURATION OF THE PT2 CARD
INDICATOR STATE EXPLANATION
COL (green) On Ethernet collision
LINK (green) On
Status of the Ethernet link:
Good link with the Ethernet switch
TX (green) On LAN transmitting
RX (green) On LAN receiving
RUN (green) Flashing slowly
Flashing rapidly
Card downloading status:
Loading software
Card in operation
NRA (red) On Internal failure detected
DESIGNATION CONFIGURATION (1)
Operating mode:
• normal mode
• programming mode (programming the flash memory
using the
programming tool card)
CA1 on OFF
CA1 on ON
- 01/2011 Page 1 1
- Page 2 01/2011 Préliminaires 2
- Page 4 01/2011 4
- Page 6 01/2011 6
- Page 8 01/2011 8
- Page 10 01/2011 10
- Page 12 01/2011 12
- Page 14 01/2011 14
- Page 16 01/2011 16
- LIST OF TABLES 17
- Page 18 01/2011 18
- Page 20 01/2011 20
- LIST OF PLATES 21
- Page 22 01/2011 22
- LIST OF FIGURES 23
- Page 24 01/2011 24
- UCV-D(A)/RUCV-D(A)) 160 24
- UCV-D(B)-RUCV-D(B)) 160 24
- Page 26 01/2011 26
- 1 Introduction 27
- Page 28 01/2011 Introduction 28
- 1.3 Reference documents 29
- 1.4 Abbreviations 30
- 1.5 Terms and expressions 31
- 1.6 Definition 31
- Page 32 01/2011 Introduction 32
- Page 34 01/2011 Introduction 34
- Page 36 01/2011 Introduction 36
- 2 Présentation 37
- Page 38 01/2011 Présentation 38
- 2.2.1 Aastra XD 39
- 2.2.2 Aastra XS/XL 40
- 2.3 Overview of the functions 41
- Page 42 01/2011 Présentation 42
- 3.1 Physical description 43
- 3.1.1.1 Internal description 44
- Figure 3.1 O 45
- EAR VIEW OF AN AXD CABINET 46
- BTX card 47
- Ventilation modu 48
- Power supply module (p 49
- Power supply module (pow 49
- RUCV-D card (A) 50
- UCV-D card (A) 50
- Power supply module 52
- IUCV-D card 54
- RUCV-D card (B) 54
- UCV-L card 56
- EAR VIEW OF AN AXL CABINET 57
- RUCV-L card 58
- RUCV-L cards 59
- 3.1.4 Internal description 61
- UCV-Scard 62
- RUCV-Scard 63
- 3.1.5.1 Control keys 65
- 3.1.5.2 Internal description 66
- EXT1-S12 67
- 3.1.6.1 Control keys 69
- 3.1.6.2 Internal description 70
- EXT1-S6 card 71
- 3.2 Characteristics 73
- +5 V / 15 A and -5 V / 0.5 A 74
- -48 V / 2.9 A 74
- 3.3 Capacity 76
- 3.4 Physical breakdown 77
- 3.4.2 Aastra XS/XL 82
- 12 12 12 82
- 3.5 Configuration rules 84
- 3.5.2 AXL iPBX 87
- 3.5.2.1 AXL main cabinet 87
- BACKPLANES OF AN AXL IPBX 90
- 3.5.3 AXS/AXS12/AXS6 iPBX 91
- 3.8.1.5 Defence function 95
- 3.8.3 Duplication (Aastra XD) 97
- (Plate 9.4) 102
- 3.8.5 Defence chain 102
- 3.8.5.1 Overview 102
- 3.8.5.2 Monitoring 103
- 3.8.5.3 Alarm management 103
- 3.8.5.4 Self protection 104
- 3.8.6.1 Aastra XD 104
- SIMPLEX CONFIGURATION 106
- CONFIGURATION 107
- 3.8.6.2 Aastra XS/XL 108
- #/&&2%4 109
- 3.8.7.1 Battery 112
- 3.8.7.1.1 Description 112
- 3.8.7.1.2 INSTALLATION 118
- 3.8.7.2 Ventilation 118
- 3.9.2 Standard configuration 119
- 3.9.6 Hospital configuration 119
- 3.10 The user interface 120
- 4.1 Expansion cards 121
- 4.1.2 Loading CLX cards 123
- 4.2 Power supply module 124
- 4.2.1.3 Monitoring 125
- 4.2.1.4 Physical description 125
- 4.2.2 ADS 300XD (AXD iPBX) 127
- 4.2.2.1 Description 127
- 4.2.2.3 Monitoring 128
- 4.2.3 ADS 350X (AXL iPBX) 130
- 4.2.3.1 Description 130
- 4.2.3.3 Monitoring 131
- 4.2.4 ADS 300X (AXL iPBX) 134
- 4.2.4.1 Description 134
- 4.2.4.3 Monitoring 135
- 4.2.5.1 Description 138
- 4.2.5.3 Monitoring 138
- 4.2.5.4 Physical description 138
- 4.3 UCV-D card 140
- EIP card No. 2 141
- EIP card No. 1 141
- VERVIEW OF THE UCV-D CARD 142
- 4.3.2 Physical description 143
- (1) Connector front view 144
- 4.3.2.1 Indicators 145
- 4.3.4 Installation and wiring 146
- 4.4 IUCV-D card 148
- VERVIEW OF THE IUCV-D CARD 150
- 4.4.2 Physical description 151
- 4.4.2.1 Connectors 152
- IUCV CARD RELAY CONTACTS 154
- 4.4.2.2 Indicators 155
- 4.4.4 Installation and wiring 156
- 4.5 RUCV-D card 157
- VERVIEW OF THE RUCV-D CARD 158
- 4.5.4 Installation and wiring 159
- 4.6 UCV-L card 164
- VERVIEW OF THE UCV-L CARD 166
- 4.6.2 Physical description 167
- 4.6.2.1 Connectors 167
- 4.6.2.2 Indicators 172
- 4.6.4 Installation and wiring 174
- 4.7 UCV-S cards 175
- VERVIEW OF THE UCV-S CARD 176
- 4.7.2 Physical description 177
- 4.7.2.1 Connectors 177
- 4.7.2.2 Indicators 180
- 4.7.4 Installation and wiring 183
- 4.8 EXT1-S card 184
- VERVIEW OF THE EXT1-S CARD 185
- 4.8.2 Physical description 186
- 4.8.2.1 Connectors 186
- 4.8.2.2 Indicators 187
- 4.8.5 Installation and wiring 190
- 4.9 EXT1-S12 card 191
- VERVIEW OF THE EXT1-S12 CARD 192
- 4.9.2 Physical description 193
- 4.9.2.1 Connectors 193
- 4.9.2.2 Indicators 193
- 4.10 EXT1-S6 card 197
- 4.10.2 Physical description 198
- 4.10.2.1 Connectors 198
- 4.10.2.2 Indicators 198
- 4.11 RUCV-L card 202
- 4.11.2.2 Indicators 203
- VERVIEW OF THE RUCV-L CARD 205
- 4.12 RUCV-S card 206
- VERVIEW OF THE RUCV-S CARD 208
- 4.13 Application cards (CLX) 209
- Connectors 210
- LD4 card 210
- LD4 CARD FRONT PANEL 210
- 4.13.2 Hardware configuration 212
- MICROSWITCH CA2.2 212
- Caution: 213
- WIRING AN S0 BUS 214
- 4.13.3 LD4NX card 217
- 4.13.3.1 Description 217
- LD4NX CARD FRONT PANEL 219
- LD4NX CARD 219
- 4.13.3.3 Physical description 220
- NAME STATE EXPLANATION 221
- Pushbuttons 222
- The front panel includes: 222
- 4.13.4 LT2 card 228
- 4.13.4.1 Description 228
- LT2 CARD 229
- LT2 CARD FRONT PANEL 229
- 4.13.5 PT2 card 238
- 4.13.5.1 Overview 238
- PT2 CARD 239
- PT2 CARD FRONT PANEL 239
- using the 241
- Carte PT2 242
- 4.13.6 CS1 card 243
- 4.13.6.1 Description 243
- CS1 CARD 244
- CS1 CARD FRONT PANEL 244
- 4.13.6.2 Physical description 245
- 4.13.6.3 Connectors 245
- 4.13.6.6 CA1 card 249
- 4.13.6.7 Description 249
- Tableau 4.62 250
- 4.13.7 CP1 card 254
- 4.13.7.1 Description 254
- 4.13.8 MUM card 256
- 4.13.8.1 Description 256
- MUM CARD 257
- MUM CARD FRONT PANEL 257
- Sync Serial Wan 258
- Interface 258
- 4.14 Equipment cards 260
- LA16X CARD 261
- WIRING AN LAX OR LMX CARD 263
- 4.14.2 LA16X-8 card 264
- 4.14.2.1 Description 264
- VERVIEW OF THE LA8 CARD 266
- 4.14.5 LN16X card 268
- 4.14.5.1 Description 268
- 4.14.6 LN16X-8 card 271
- 4.14.6.1 Description 271
- 4.14.8 LN8 card 274
- 4.14.8.1 Description 274
- VERVIEW OF THE LN8 CARD 275
- 4.14.9 LM8 card 276
- 4.14.9.1 Description 276
- 4.14.10 LH8 card 278
- 4.14.10.1Description 278
- LH8 CARD 279
- LH8 CARD FRONT PANEL 279
- 4.14.11 LH16X card 280
- 4.14.11.1 Description 280
- 4.14.12 LH16X-8 card 282
- 4.14.12.1Description 282
- 4.14.13 LR4 card 284
- 4.14.13.1Description 284
- LR4 CARD 285
- LR4 CARD FRONT PANEL 285
- S1.X.3 S1.X.4 SWITCH GAIN 287
- Detection threshold [dBm]: 288
- • -3 to -32 dBm 288
- CA1.4 on ON 288
- 4.14.14 LI1 card 289
- 4.14.14.1Description 289
- VERVIEW OF THE LI1 CARD 291
- LI1 CABLE 294
- CONNECTOR/ 295
- EQUIPMENT 295
- 4.14.15 BTX card 298
- 4.14.15.1Description 298
- Indicators 300
- 5.1 Digital sets 301
- 5.2 Analogue sets 302
- 5.3 IP sets 303
- 5.4 Computer terminals 304
- 5.5 Attendant consoles (ATDC) 305
- 5.6 Miscellaneous equipment 306
- 5.6.2.2 Installation 307
- 5.6.3 Alarm bell 307
- 5.6.3.1 Description 307
- 5.6.3.2 Installation 308
- 6 INSTALLATION AND ACTIVATION 309
- 6.2.1 Preliminary operations 310
- 6.2.1.1 Site inspection 310
- 6.2.1.2 Location 310
- 6.2.1.3 Environment 311
- 6.2.1.4 Space 311
- 6.2.1.5 Earth connection 312
- Caption: 313
- 1- Product description 313
- 2- Product sales code 313
- INSTALLATION 314
- Installation in a rack 315
- Table 1: 316
- Installation 318
- PRÉSENTATION 319
- CONTRAINTE 319
- : Operating 323
- Do you confirm (Y/N)? 325
- Section 6.2.7) 326
- 6.2.6.2.1 Connectors 329
- Windows PC specifications 330
- SSH protocol 337
- ADMINISTRATION NETWORK menu 339
- Call Dist 343
- Subscribers 345
- TELEPHONY/SYSTEM/ 349
- 6.3.1 Equipment checklist 351
- 6.3.2 Handling cards 352
- • Save the configuration 354
- J13: EIP CARD NO. 1 357
- J14: EIP CARD NO. 2 358
- (see AMP operating manual) 362
- Portal operating manual 369
- 6.7.1 Principle 371
- 6.7.2.1 Loading update files 372
- 6.7.2.1.1 By PC import 372
- 6.7.2.2.2 By USB key 375
- 6.7.2.3 Switchover 376
- Delete" checkbox: 377
- 6.8.1 Principle 378
- 6.11 Remote access modes 381
- 6.11.3.1 CONNECTIONS 388
- COMPACT FLASH 389
- CARD SIZE 389
- DURATION 389
- NUMBER OF 389
- VOICEMAIL BOXES 389
- 6.12.1 Migration process 390
- 6.12.1.2.1Procedure 390
- 6.12.1.2.2Error messages 391
- 6.12.1.5.1Pre-requisites 393
- 6.12.1.5.2Procedure 393
- 6.12.1.5.3Error messages 394
- 7 Maintenance 395
- 7.2.2 Maintenance resources 396
- 7.2.3 Preventive maintenance 397
- 7.2.4 Corrective maintenance 397
- 7.2.5 Restarting 398
- Maintenance 01/2011 Page 399 399
- IUCV-D (without i-button) 399
- Page 400 01/2011 Maintenance 400
- Equipment cards 400
- Maintenance 01/2011 Page 401 401
- ASSEMBLIES (1/2) 401
- SUB-ASSEMBLIES (2/2) 402
- 7.2.7.4 Interchangeable fuses 403
- 7.2.7.9 Mounting kits 404
- 7.3 Alarm messages and codes 405
- 7.4 Corrective maintenance 406
- E-X SHEET 407
- 7.4.1.3 Guidelines 408
- 7.4.2 List of E sheets 409
- AVAILABILITY 410
- OPERATORS (s) 410
- INGRÉDIENT(S)/CONSOMMABLE(S) 410
- PROCEDURE 411
- Maintenance 01/2011 Page 415 415
- Page 416 01/2011 Maintenance 416
- Table 5: 416
- Page 418 01/2011 Maintenance 418
- Table 7: 418
- Maintenance 01/2011 Page 421 421
- Page 422 01/2011 Maintenance 422
- Table 10: 422
- Page 424 01/2011 Maintenance 424
- Table 11: 424
- Maintenance 01/2011 Page 425 425
- REPLACING A UCV-D CPU CARD 426
- Maintenance 01/2011 Page 427 427
- AMP (see document [1]) 427
- Page 428 01/2011 Maintenance 428
- Table 14: 428
- REPLACING A RUCV-D CARD 430
- Table 15: 431
- Page 432 01/2011 Maintenance 432
- Table 16: 432
- REPLACING AN IUCV-D CARD 434
- Table 17: 435
- Table 18: 437
- Page 438 01/2011 Maintenance 438
- Page 440 01/2011 Maintenance 440
- Table 19: 440
- Table 20: 441
- • Disconnect the mains cable 441
- Page 442 01/2011 Maintenance 442
- Maintenance 01/2011 Page 445 445
- Table 22: 447
- 450 01/2011 Maintenance 450
- 9 FUNCTIONAL DIAGRAMS 453
- MT/PTD/PBX/0058/4/6/EN 456
- 10.1 Important pre-requisite 459
- Name&IID 465
- Server network card 470
- Properties" menu 473
- Launcher" tab 473
- 10.8.1 Principle 477
- 10.8.2 Upgrading Red Hat 5.4 477
- 10.9.1 Principle 479
- Two media types can be used: 480
- • USB key 480
- 10.9.2.1.1By PC import 481
- 10.9.2.2.2By USB key 483
- 10.9.3 Switchover 484
- 11 APPENDICES 487
- 488 01/2011 Appendices 488
- 490 01/2011 Appendices 490
- 492 01/2011 Appendices 492
- 494 01/2011 Appendices 494
- Appendices 01/2011 Page 495 495
- 11.4.1 Considerations 496
- 11.4.2 Introduction 496
- 11.4.3.1 Structure 497
- 11.4.3.2 Instructions for use 497
- 498 01/2011 Appendices 498
- 500 01/2011 Appendices 500
- 11.4.5 Selection keys tab 501
- 11.4.6 Multi-lines tab 502
Relacionado con productos y manuales para Servidores Aastra AXD
Servidores Aastra AXD Manual de usuario
(595 paginas)
(595 paginas)
Servidores Aastra 5000 Guía de usuario
(64 paginas)
(64 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales